MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the first end.AAGZ
First End Style:
Plain
MRC:
A term used to identify the ends as identical or not identical.AAHN
End Similarity:
Not identical
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the second end.AAHP
Second End Style:
Flat groove and woodruff keyway
MRC:
The dimension measured along the longitudinal axis with terminated points at the extreme ends of the item.ABHP
Overall Length:
89.2500 inches
MRC:
The national stock number or the identification information of the end equipment for which the item is a part.AGAV
End Application:
Hangar division doors used on aircraft carrier cvn 74
MRC:
The length of a straight line which passes through the center of the first end,and terminates at the circumference.AMDL
First End Diameter:
Between 8.4980 inches and 8.5000 inches
Second End Distance From End To Flat:
0.7500 inches
MRC:
A measurement taken at right angles to the length of the keyway at the second end,in distinction from thickness.AMFR
Second End Keyway Width:
2.0000 inches
Second End External Keyway Length:
7.0000 inches
Second End Distance From Keyway Center To End:
5.0000 inches
MRC:
The length of a straight line which passes through the center of the second end,and terminates at the circumference.AMFZ
Second End Diameter:
Between 8.2490 inches and 8.2500 inches
Second End Grooved Flat Length:
0.5000 inches
Second End Grooved Flat Depth:
1.1250 inches
MRC:
The number of steps provided.ATPC
Step Quantity:
6
MRC:
The length of a straight line which passes through the center of the largest step,and terminates at the circumference.CSPY
Largest Step Diameter:
8.9375 inches
MRC:
Designates the specific surface roughness rating,representing the arithmetic average deviation of the surface from the meanline in profile.CSYM
Surface Finish:
63.0 microinches
MRC:
Those unusual or unique characteristics or qualities of an item not covered in the other requirements and which are determined to be essential for identification.FEAT
Special Features:
All keyways to have a 0.0625 radius in bottom corners; from second end, steps up at 9.2500 inches to 8.5000 inches diameter, steps up at 18.7500 inches to 8.5620 inches diameter, steps up at 28.5000 inches to 8.9375 inches diameter, steps down at 67.5000 inches to 8.5100 inches diameter; steps down at 80.1562 to 8.5000 inches diameter; two 2.0000 inches wide x 0.7500 inches deep keyways, first one starts at 9.0938 inches and stops at 21.0938 inches from first end, second one starts at 19.1250 inches and stops at 28.1250 inches from second end; both ends have 0.1250 inches x 45 degree chamfer
MRC:
The chemical compound or mechanical mixture properties of which the item is fabricated.MATT
Material:
Steel
MRC:
The specification,standard,or manufacturers reference,and the classification designation,such as class,condition,temper,and the like,that identifies the material.MDCL
Material Specification:
Mil-s-24093 cl-e type i, ii, or iii military specification single material response or aisi 4140 or b7 assn standard single material response
MRC:
Test conditions and ratings,or environmental and performance requirements that are different,more critical,or more specific than those specified in a governing test data document.SPCL
Special Test Features:
Magnetic particle tested (mt) in accordance with reference number 6, after final machining. Indications shall not exceed 0.1250 inches in length or any 6 square inches area that exhibits ten or more defects of less than 0.1250 inches in length. Large defects may be repaired by welding
