부품 정보
The hose braid, end fittings and springs shall be fabricated from austenitic steel of low magnetic permeability
TXT
묘사:
Nonmetallic Hose Assembly
MRC:
The style designation indicating the configuration that most nearly corresponds to the cross-sectional shape of the item.AAGR
Cross Sectional Shape:
Round
MRC:
The direction of the thread when viewed axially. a right-hand thread winds in a clockwise direction while a left-hand thread winds in a counterclockwise direction.AAJF
Thread Direction:
Right-hand 1st end
MRC:
The length of a straight line which passes through the center of a circular figure or body,and terminates at the inside circumference.AARX
Inside Diameter:
0.250 inches
MRC:
A value which expresses the degree of heat or cold as applied to the operation,or limitation of operation,of an item.ABJH
Tempurature Rating:
0.0 degrees fahrenheit single response and 150.0 degrees fahrenheit single response
MRC:
A value which expresses the degree of heat or cold as applied to the operation,or limitation of operation,of an item.ABJH
Tempurature Rating:
0.0 degrees fahrenheit and 150.0 degrees fahrenheit single response
MRC:
The length of a straight line which passes through the center of a circular figure or body,and terminates at the outside circumference.ABKV
Outside Diameter:
0.688 inches
MRC:
The minimum inside bending radius formed without stressing or deformation of a flexible item.ACKH
Minimum Inside Bending Radius:
4.000 inches
MRC:
The hue or tint of the exterior of the item.ADJS
Exterior Color:
Black
MRC:
The specification or standard /industrial or governmental/ that specifically covers the construction of the hose or tubing,excluding the end fittings.ADLF
Hose Or Tubing Specification/std Data:
Mil-h-24239 specification (includes engineering type bulletins, brochures, etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical", "average", "", etc.).
MRC:
The specification or standard /industrial or governmental/ that specifically covers one complete end fitting.ADLG
First End Fitting Specification/std Data:
Mil-h-24239 specification (includes engineering type bulletins, brochures, etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical", "average", "", etc.).
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the connection.AHNC
Connection Style:
Plain 1st end
MRC:
The physical configuration of the outside of the end connection.AKUU
End Connection Design:
Straight 1st end
MRC:
The name of the fitting and/or component and the element, compound, or mixture of which it is fabricated.AKXL
End Fitting Component And Material:
Nipple steel comp 302 all ends
MRC:
The name of the fitting and/or component and the element, compound, or mixture of which it is fabricated.AKXL
End Fitting Component And Material:
Socket steel comp 302 1st end
MRC:
The name of the fitting and/or component and the plating, dip and/or coatingthat cannot be wiped off. plating and/or coating is any chemical and/or metallic additive, electrochemical or mild mechanical process which protects the surface.AKXM
Fitting Component And Surface Treatment:
Nipple passivate all ends
MRC:
The name of the fitting and/or component and the plating, dip and/or coatingthat cannot be wiped off. plating and/or coating is any chemical and/or metallic additive, electrochemical or mild mechanical process which protects the surface.AKXM
Fitting Component And Surface Treatment:
Socket passivate 1st end
MRC:
Indicates the type of connection/s/.AWLS
Connection Type:
Threaded external pipe 1st end
MRC:
Those features,not otherwise specified,which may be required for proper functioning of the item.CBBL
Features Provided:
Electrostatic discharge capability
MRC:
The number of threads on the item per linear inch measured on a line parallel to the thread axis.CMLP
Thready Qty Per Inch (tpi):
18 1st end
MRC:
Indicates whether or not the second end is identical to the first end.CQBB
Second End Relationship With First End:
Identical
MRC:
The minimum internal pressure rating,determined by destruction tests,at which the item can be expected to rupture.CQBD
Burst Test Pressure:
12000.0 pounds per square inch
MRC:
An indication of whether or not the end has the capability to rotate.CQBG
First End Swivel Action Capability:
Not included
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
1st layer braided cotton cord err-100
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
2nd layer molded rubber err-100
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
3rd layer braided corrosion resistant steel wire err-100
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
Outer layer molded rubber err-100
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
1st layer braided cotton cord
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
3rd layer braided corrosion resistant steel wire
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
Outer layer molded rubber
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
2nd layer molded rubber
MRC:
The maximum pressure at which the item is rated for operation.CQGM
Maximum Operating Pressure:
3000.0 pounds per square inch
MRC:
A designation that is used for the purpose of general identification of the thread.CQJX
Thread Size:
0.250 inches 1st end
MRC:
The angle of the end surface upon which the mated surface seats.CQRB
Seat Angle:
90.0 degrees 1st end
MRC:
A steady,uniform,internal,static pressure that the item must withstand without leakage,abnormal distortion,or damage.CRDW
Hydrostatic Test Pressure:
6000.0 pounds per square inch
MRC:
The type of protection provided by the outer covering.CRJM
Outer Covering Environmental Protection:
Abrasion resistant and mildew resistant and oil resistant
MRC:
The condition of the item with respect to the texture of the inner surface.CRWL
Inside Surface Condition:
Smooth
MRC:
Those unusual or unique characteristics or qualities of an item not covered in the other requirements and which are determined to be essential for identification.FEAT
Special Features:
Inner conveying tube material-rubber, synthetic; the hose braid, end fittings and springs shall be fabricated from austenitic steel of low magnetic permeability
MRC:
The type of media for which the item is designed.MEDA
Media For Which Designed:
Hydraulic fluid, silicate-ester base single response
MRC:
The specification,standard,drawing,or similar instrument that specifies environmental and performance requirements or test conditions under which an item is tested and establishes acceptable limits within which the item must conform identified by an alphabetic and/or numeric reference number. includes the commercial and government entity (cage) code of the entity controlling the instrument.TEST
Test Data Document:
81349-milh24239 specification (includes engineering type bulletins, brochures, etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical", "average", "", etc.).
MRC:
A designation distinguishing one group of thread diameter-pitch combinations from another by the number of threads per measurement scale for a specific diameter.THSD
Thread Series Designator:
Npt 1st end
