TXT
묘사:
Electrical Resolver
MRC:
The basic material of which the body is fabricated.AAFZ
Body Material:
Steel, corrosion resisting
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the body.AAQL
Body Style:
Standard round b
MRC:
The length of a straight line which passes through the center of a shoulder,and terminates at the circumference.AAVH
Shoulder Diameter:
Between 1.3115 inches and 1.3120 inches
MRC:
The length of a straight line which passes through the center of that portion used to guide the item and terminates at the circumference.AAVL
Pilot Diameter:
Between 0.8745 inches and 0.8750 inches
MRC:
The dimension measured along the longitudinal axis with terminated points at the extreme ends of the item.ABHP
Overall Length:
2.4560 inches
MRC:
The length of a straight line which passes through the center of a flange,and terminates at the circumference.ABKK
Flange Diameter:
Between 1.4340 inches and 1.4370 inches
MRC:
A measurement of the smallest dimension of a flange,in distinction from length or width.ABKU
Flange Thickness:
0.0930 inches
Undercut Width:
0.0780 inches
MRC:
The length of a straight line which passes through the center of a shaft,and terminates at the circumference.ABWV
Shaft Diameter:
0.1870 inches single shaft and 0.1872 inches single shaft
MRC:
A measurement of the longest dimension of the shaft,in distinction from width.ABXF
Shaft Length:
0.5550 inches single shaft
MRC:
The measure of sensitivity of the item to be packaged. a factor used by packaging engineers in devising proper cushioning in a package.AFJN
Fragility Factor:
Moderately rugged
MRC:
An alpha and/or numeric designation indicating the size by which the body is identified.AJSL
Body Size:
15
MRC:
The value of the primary excitation voltage for which the stator is rated,expressed in volts.AJSN
Stator Input Voltage Rating In Volts:
26.0
MRC:
The cycles per second /hertz/ of the alternating current.AJSS
Frequency In Hertz:
400.0
MRC:
The magnitude part /z/ of the stator impedance with the rotor open /zso/,expressed in ohms.AJTJ
Zso Impedance Magnitude In Ohms:
2550.00
MRC:
The angle part /o/ of the stator impedance with the rotor open /zso/,expressed in degrees.AJTK
Zso Impedance Angle In Deg:
79.00
MRC:
The opposition that the rotor offers to the flow of the direct current,expressed in ohms.AJTS
Rotor Dc Resistance In Ohms:
320.00
MRC:
The opposition that the stator offers to the flow of direct current,expressed in ohms.AJTT
Stator Dc Resistance In Ohms:
390.00
MRC:
The means utilized to vary the level of signal input or response to attain the desired operational action.AJTX
Compensation Method:
Winding compensated
MRC:
The opposition that the compensator offers to the flow of direct current,expressed in ohms.AJVC
Compensator Dc Resistance In Ohms:
520.00
MRC:
The ratio of the fundamental component of the no-load secondary voltage to the compensator voltage at maximum coupling,expressed in percent.AJVD
Compensator Transformation Ratio In Percent:
0.990 rotor to compensator
MRC:
The difference between the phase time of two or more voltages or currents of the same frequency,at the same instant of time,expressed in degrees.AJVF
Phase Shift Angle In Deg:
8.500 input to output
MRC:
The maximum voltage,without harmonics,induced in the secondary circuit at the null angle rotor position,expressed in millivolts per volt.AJVG
Maximum Fundamental Null Voltage In Millivolts Per Volt:
8.00 output
MRC:
The maximum voltage,including harmonics,induced in the secondary circuit at the null angle rotor position,expressed in millivolts per volt.AJVH
Maximum Total Null Voltage Output In Millivolts Per Volt:
15.00
MRC:
The number of individual teeth on the splined portion of the shaft.AJVM
Spline Tooth Quantity:
21 single shaft
MRC:
The amount of rotary force that must be applied to the actuator to cause rotation,at plus 25 degrees celsius.AJVT
Actuator Friction Torque At Plus 25 Deg Celsius:
0.15 inch-ounces
MRC:
A measurement of the longest dimension of a pilot,in distinction from width.AJWQ
Pilot Length:
0.0400 inches
Shoulder Length:
0.1320 inches
Mounting Surface To Terminal End Distance:
1.9160 inches
MRC:
The number of teeth the splined shaft has per inch of pitch diameter.AJXA
Spline Tooth Diametral Pitch:
120 single shaft
MRC:
A designation distinguishing one group of shaft thread diameter-pitch combinations from another by the number of threads per measurement scale for a specific diameter.AJYY
Shaft Thread Series Designator:
Unf single shaft
MRC:
The direction of the shaft thread when viewed axially. a right-hand thread winds in a clockwise direction while a left-hand thread winds in a counterclockwise direction.AKAF
Shaft Thread Direction:
Right-hand single shaft
MRC:
A numeric-alpha designator indicating the ptich diameter tolerance,and an external or internal shaft thread.AKAN
Shaft Thread Class:
2a single shaft
MRC:
Indicates the location of the terminal/s/ on the item.CQTM
Terminal Location:
Rear
MRC:
A measurement of the extent of the shaft threads measured on a line parallel to the longitudinal axis.CQWQ
Shaft Thread Length:
0.1590 inches single shaft
MRC:
Indicates the type of shaft included on the item.CRSJ
Shaft Type:
Spline w/threads single shaft
MRC:
The ratio of the output voltage to the input voltage at maximum coupling.CSJY
Transformation Ratio:
0.980 rotor to stator
MRC:
The length of a straight line passing through the center of the shaft threaded portion,with terminated points at the circumference.CWBH
Shaft Thread Size:
0.190 inches single shaft
MRC:
Indicates the type and number of terminals for providing electrical connection.TTQY
Terminal Type And Quantity:
12 screw
