부품 정보
Hose assembly, straight, flg
TXT
묘사:
Nonmetallic Hose Assembly
MRC:
The style designation indicating the configuration that most nearly corresponds to the cross-sectional shape of the item.AAGR
Cross Sectional Shape:
Round
MRC:
The length of a straight line which passes through the center of a circular figure or body,and terminates at the inside circumference.AARX
Inside Diameter:
6.073 inches
MRC:
A value which expresses the degree of heat or cold as applied to the operation,or limitation of operation,of an item.ABJH
Tempurature Rating:
-40.0 degrees fahrenheit and 200.0 degrees fahrenheit single response
MRC:
The length of a straight line which passes through the center of a circular figure or body,and terminates at the outside circumference.ABKV
Outside Diameter:
6.834 inches
MRC:
The minimum inside bending radius formed without stressing or deformation of a flexible item.ACKH
Minimum Inside Bending Radius:
42.000 inches
MRC:
The number of bolt holes provided on the item.AECS
Bolt Hole Quantity:
12 1st end
MRC:
The length of a straight line which passes through the center of the flange,and terminates at the outside circumference.AEPR
Flange Outside Diameter:
9.410 inches 1st end
MRC:
The national stock number or the identification information of the end equipment for which the item is a part.AGAV
End Application:
Misc parts list for ac-cw, piping pump discharge to bank engine room, virginia class ssn
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the connection.AHNC
Connection Style:
Raised swivel 1st end
MRC:
A measurement from the bottom to the top surface of a raised face,in distinction from depth.AJED
Raised Face Height:
0.015 inches 1st end
MRC:
The length of a straight line which passes through the center of a raised face,and terminates at the circumference.AJEE
Raised Face Diameter:
7.370 inches 1st end
MRC:
The design used in constructing the end portion of the flange.AKUT
End Flange Construction:
Solid 2nd end
MRC:
The design used in constructing the end portion of the flange.AKUT
End Flange Construction:
Split 1st end
MRC:
Indicates the type of connection/s/.AWLS
Connection Type:
Raised face flange 1st end
MRC:
Indicates the type of connection/s/.AWLS
Connection Type:
Plain face flange 2nd end
MRC:
The number of threads on the item per linear inch measured on a line parallel to the thread axis.CMLP
Thready Qty Per Inch (tpi):
14 1st end
MRC:
The minimum internal pressure rating,determined by destruction tests,at which the item can be expected to rupture.CQBD
Burst Test Pressure:
1200.0 pounds per square inch
MRC:
The material and formation identifying the structural characteristic/s/ of the item and location.CQCS
Layer Composition And Location:
1st layer spirally wrapped fabric and outer layer rubber composition
MRC:
The maximum pressure at which the item is rated for operation.CQGM
Maximum Operating Pressure:
300.0 pounds per square inch
MRC:
The means used and the measurement of the longest dimension of an item.CRXX
Measuring Method And Length:
33.000 inches excluding end fittings
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the flange.CTCJ
Flange Style:
Round w/ bolt holes 1st end
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the flange.CTCJ
Flange Style:
Round w/ out bolt holes 2nd end
MRC:
Those unusual or unique characteristics or qualities of an item not covered in the other requirements and which are determined to be essential for identification.FEAT
Special Features:
Assy includes: 1 hose, syn rubber, 6.000 in i.D. X 6.880 in, 300 psi, 33.000 in long, low pressure (p/n f242-1), 2 elbows, 90 deg, hose x flg -96 hose x 6.000 nps (p/n f242-2), 1 tag assembly, hose, 4.000 to 8.000 in diameter per 96169/2633-225-01, sheet 4-6 (p/n f242-3)
MRC:
The type of media for which the item is designed.MEDA
Media For Which Designed:
Water, salt single response
MRC:
A designation distinguishing one group of thread diameter-pitch combinations from another by the number of threads per measurement scale for a specific diameter.THSD
Thread Series Designator:
Nps 1st end
MRC:
The document designator of the specification or standard which established the item of supply.ZZZK
Specification Data:
81349-mil-h-24136/1 government specification
