TXT
묘사:
Electrical Resolver
MRC:
The basic material of which the body is fabricated.AAFZ
Body Material:
Steel, stainless
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the body.AAQL
Body Style:
Standard round b
MRC:
The length of a straight line which passes through the center of a shoulder,and terminates at the circumference.AAVH
Shoulder Diameter:
Between 1.3115 inches and 1.3120 inches
MRC:
The length of a straight line which passes through the center of that portion used to guide the item and terminates at the circumference.AAVL
Pilot Diameter:
Between 0.8745 inches and 0.8750 inches
MRC:
The dimension measured along the longitudinal axis with terminated points at the extreme ends of the item.ABHP
Overall Length:
Between 2.5580 inches and 2.6050 inches
MRC:
The length of a straight line which passes through the center of a flange,and terminates at the circumference.ABKK
Flange Diameter:
Between 1.4360 inches and 1.4370 inches
MRC:
A measurement of the smallest dimension of a flange,in distinction from length or width.ABKU
Flange Thickness:
0.0930 inches
Undercut Width:
0.0780 inches
MRC:
The length of a straight line which passes through the center of a shaft,and terminates at the circumference.ABWV
Shaft Diameter:
0.1871 inches single shaft and 0.1873 inches single shaft
MRC:
A measurement of the longest dimension of the shaft,in distinction from width.ABXF
Shaft Length:
0.5710 inches single shaft
MRC:
An alpha and/or numeric designation indicating the size by which the body is identified.AJSL
Body Size:
15
MRC:
The value of the primary excitation voltage for which the stator is rated,expressed in volts.AJSN
Stator Input Voltage Rating In Volts:
30.0
MRC:
The value of the primary excitation current for which the stator is rated,with rotor /secondary/ circuit open.AJSP
Stator Input Current Rating:
10.0 milliamperes
MRC:
The cycles per second /hertz/ of the alternating current.AJSS
Frequency In Hertz:
400.0
MRC:
The opposition that the rotor offers to the flow of the direct current,expressed in ohms.AJTS
Rotor Dc Resistance In Ohms:
200.00
MRC:
The opposition that the stator offers to the flow of direct current,expressed in ohms.AJTT
Stator Dc Resistance In Ohms:
295.00
MRC:
The means utilized to vary the level of signal input or response to attain the desired operational action.AJTX
Compensation Method:
Winding compensated
MRC:
The opposition that the compensator offers to the flow of direct current,expressed in ohms.AJVC
Compensator Dc Resistance In Ohms:
295.00
MRC:
The ratio of the fundamental component of the no-load secondary voltage to the compensator voltage at maximum coupling,expressed in percent.AJVD
Compensator Transformation Ratio In Percent:
1.000 rotor to compensator
MRC:
The difference between the phase time of two or more voltages or currents of the same frequency,at the same instant of time,expressed in degrees.AJVF
Phase Shift Angle In Deg:
5.000 input to output
MRC:
The deviation from 90 degrees perpendicularity of the secondary winding,when excitation is applied to one of the primary windings,expressed in minutes.AJVJ
Interaxis Error Angular Range In Minutes:
-5.0/+5.0
MRC:
The limits of permissible deviation of the actual output voltage form the theoretical sinusoidal output voltage divided by the maximum output,expressed in percent.AJVK
Output Voltage Functional Error Range In Percent:
-0.1/+0.1
MRC:
The number of holes provided for aligning the item.AJVW
Alignment Hole Quantity:
4
MRC:
A measurement of the longest dimension of a pilot,in distinction from width.AJWQ
Pilot Length:
0.0400 inches
Shoulder Length:
0.1320 inches
Mounting Surface To Terminal End Distance:
1.7910 inches
MRC:
Indicates the location of the terminal/s/ on the item.CQTM
Terminal Location:
Rear
Shaft Slot Depth:
0.0300 inches single shaft
Shaft Slot Width:
0.0300 inches single shaft
MRC:
Indicates the type of shaft included on the item.CRSJ
Shaft Type:
Round, slotted single shaft
Alignment Hole Depth:
0.1870 inches
MRC:
The ratio of the output voltage to the input voltage at maximum coupling.CSJY
Transformation Ratio:
0.985 rotor to stator
Alignment Hole Bolt Circle Diameter:
0.8750 inches
MRC:
The specification,standard,drawing,or similar instrument that specifies environmental and performance requirements or test conditions under which an item is tested and establishes acceptable limits within which the item must conform identified by an alphabetic and/or numeric reference number. includes the commercial and government entity (cage) code of the entity controlling the instrument.TEST
Test Data Document:
89264-c6010291 drawing (this is the basic governing drawing, such as a contractor drawing, original equipment manufacturer drawing, etc.; excludes any specification, standard or other document that may be referenced in a basic governing drawing)
MRC:
Indicates the type and number of terminals for providing electrical connection.TTQY
Terminal Type And Quantity:
12 screw
