측정 단위:
* special requirements. EA
TXT
묘사:
Hydraulic Brak Cylinder Assembly
MRC:
The basic material of which the body is fabricated.AAFZ
Body Material:
Steel
First End Outside Diameter:
0.375 inches
MRC:
The provision/s/ for mounting the item.ABDR
Mounting Provision:
Unthreaded mounting holes
MRC:
A value which expresses the degree of heat or cold as applied to the operation,or limitation of operation,of an item.ABJH
Tempurature Rating:
Not rated
MRC:
The distance measured in a straight line from the bottom to the top of an item.ABKW
Overall Height:
4.000 inches
MRC:
An overall measurement taken at right angles to the length of an item,in distinction from thickness.ABMK
Overall Width:
2.625 inches
MRC:
The length of a straight line which passes through the center of a circular bore,and terminates at the circumference.ABXV
Bore Diameter:
1.125 inches
MRC:
The means by which the item is actuated.AFLW
Actuation Method:
Direct
MRC:
The angle of the end surface upon which the mated surface seats,expressed in degrees.AJFY
Seat Angle In Deg:
Any acceptable
First End External Thread Length:
1.312 inches
MRC:
A measurement of the smallest length to which the item may be compressed,in distinction from width.AMQZ
Compressed Length:
7.969 inches
MRC:
A measurement of the longest dimension of an item when it is in an extended position,in distinction from width.ATEM
Extended Length:
9.406 inches
MRC:
The style designation indicating the configuration that most nearly corresponds to the arrangement of the mounting provision(s).BBBW
Mounting Provision Arrangement Style:
Two hole
MRC:
Indicates the type of reservoir provided.BMWH
Reservoir Type:
Integral
Straight Bore Inside Diameter:
1.125 inches
MRC:
Those features,not otherwise specified,which may be required for proper functioning of the item.CBBL
Features Provided:
Filler plug and rubber boot
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the first piston rod end.CKSF
First Piston Rod End Style:
External threaded
MRC:
A designation distinguishing one group of screw thread diameter-pitch combinations from another by the number of threads per measurement scale for a specific diameter on the first piston rod end.CKSG
First Piston Rod End Thread Series Designator:
Unf
MRC:
The length of a straight line which passes through the center of the first piston rod end which would bound the crest of an external thread or the root of an internal thread.CKSH
First Piston Rod End Thread Diameter:
0.375 inches
MRC:
The number of screw threads on the first piston rod end per linear inch measured on a line parallel to the thread axis.CKSJ
First Piston Rod End Thready Qty Per Inch (tpi):
24
MRC:
A numeric-alpha designator indicating the pitch diameter tolerance and an external or internal thread of the first piston rod end.CKSK
First Piston Rod End Thread Class:
2a
MRC:
The direction of the first piston rod end thread when viewed axially. a right-hand thread winds in clockwise direction while a left-hand thread winds in a counterclockwise direction.CKSL
First Piston Rod End Thread Direction:
Right-hand
MRC:
Indicates the type of mounting and the location on the item.CLML
Mounting Type And Location:
Boss center section
MRC:
The length of a straight line which passes through the center of the mounting facility,and terminates at the circumference.CLMQ
Mounting Facility Diameter:
0.469 inches
Center To Center Distance Between Mounting Provisions:
2.875 inches
MRC:
Indicates the location and number of ports on the item.CLMS
Port Location And Quantity:
1 cylinder head end
MRC:
The style designation indicating the configuration that most nearly corresponds to the appearance of the port.CLMT
Port Style:
Gasket seal
MRC:
A designation distinguishing one group of screw thread diameter-pitch combinations from another by the number of threads per measurement scale for a specific diameter on the port.CLMW
Port Thread Series Designator:
Unf
MRC:
The length of a straight line which passes through the center of the port and would bound the crest of an external thread or the root of an internal thread.CLMX
Port Thread Diameter:
0.500 inches
MRC:
A measurement of the number of screw threads on the port per linear inch,including incomplete threads,on a line parallel to the thread axis.CLMY
Port Thready Qty Per Inch (tpi):
20
MRC:
A numeric-alpha designator indicating the pitch diameter tolerance and an external or internal port thread.CLNB
Port Thread Class:
2b
